Home Interior Ideas

Archive for the ‘Lighting’ Category

The Advantages Of Low Energy Lights

Article by Castlegate Lights

Energy conservation is the need of the hour linked to a concern for the environment by reducing noxious emissions. This is the prime reason why a lot of awareness has been doing the rounds regarding saving the energy. One of the best ways to save energy is by reducing its usage. Most of the energy saving organisations and energy experts often urge people to ensure that there is absolutely no wastage of energy. You must have surely come across a suggestion which has warned to make sure that you switch off all the lights and other electronic appliances when they are not in use. There is no doubt whatsoever that this is surely one of the effective ways of saving energy. However, we have reached a point where saving energy would need something more than this and hence we need to look at the bigger picture.

Over the past few years, a lot of awareness has been generated regarding the use of energy efficiency lighting products. A lot of people around the world have been able to relate them to this aspect. It is a natural tendency to switch on the lights of a room that we are using. However, in most houses, high energy lights are used. If you look at this aspect logically, you would soon realise that the high energy lights are more often than not of no use in the room all the time. Ideally, the high energy light should only be used while reading or doing any other work that would require you to focus on a particular thing.

On the other hand, low energy lights would ensure that a lot of energy is saved. One of the advantages of using low energy lights is that the amount of energy saved is humungous to say the least. By using these kinds of lights you ensure that you not only save energy while they are switched off, but also while they are working.

Another extremely important advantage of using low energy lights is the reduction in your monthly electricity bill. You would be surprised to see the kind of difference these lights can have on your energy bill. A lot of people have realised this aspect and hence are willing to use low energy lights. The fact that these lights save a lot of money has even gained a lot of popularity in this time and age where expenses seem to be touching the sky and hence every individual is looking for some practical ways to cut down the daily and routine expenses.

One of the highlights of the low energy lights is that they would certainly give a new charm to the look of your house. These lights are able to create a soothing effect on the eye and low energy would also mean that it would create a cosy environment in the house. You can arrange the low energy lights in strategic locations so that the lights make the house look even more elegant. Nowadays LED lights are gaining in popularity since they have a long life and provide better lighting with substantially reduced power consumption. Compact fluorescent tubes are also energy efficient and provide a convenient alternative to strip lighting or traditional filament lamps.

About the Author

We have been in business for over 30 years and we stock a large range of light fittings, from crystal chandeliers, ultra modern, Tiffany lighting, bathroom fittings, traditional lighting, in fact, just about every style of light fitting to suit your home inside and outside. Endon, Dar, Searchlight, Kontsmide, Bell, Quality Lighting, Loxton Lighting, Interiors 1900, Impex, Firstlight, Elstead, Franklite, Eglo are some of the lighting companies we deal with. Visit Castlegate Lights today!

The Advantages Of Low Energy Lights

Related Lighting Articles

Focus lights converted – converted common mode lights – lights, conversion – Automotive repair and m

Article by jekky

Other than the vast majority of vehicles are equipped at the factory halogen headlights. Its power is generally 55W or 60W, line and lighting design basically matches the load to bear. However, many owners are on the original car that does not meet the brightness of light, especially after a period of time should use the lighting system on a number of modifications and upgrades to make your car more this pair of eyes brighter. Is below the current market for several common ways to do some light modifications on the conversion methods and principles, installation procedures and costs, effectiveness and impact such as use of comparison and characteristics in order to maintenance personnel and vehicle owners to provide some help. Current car headlight bulb specifications and models generally have H1, H4, H7, 9004,9005,9006, or 9007 and so are several. Most economy cars, mid-size car with the H4 model, which combines the dual-distance light bulb filament combination is all about a single-lamp system (such as the Pajero, cheetah, Santana, Santana 2000, Beverly , Sail, Hyundai Santa Fe, Land Cruiser, Toyota overbearing, Fit, Jinbei, Hongqi, Audi 100, etc.); and a number of senior, senior and deluxe models are widely used around the two large double headlamps lamp system, the four light system (such as the typical BMW cars, VOLVO cars, HONDA cars, GM cars, NISSAN cars, AUDI cars, LEXUS cars most of the models). Some of them use the H1-type high beam, low beam lamp H7 type (such as the Audi A6 series, the Ford family, Buick Regal, Passat, Mazda 6, Nissan Sunny, Honda Odyssey models, etc.); some with the H7 high beam type, beam lamp H1 type (such as the new Jetta, China, VOLVO and other vehicles); some distance light can use H1 or H7 type type (such as the Jetta, the new Buick Century, Buick GL8 other models); there is to use the 9005 or 9006 model (in Japanese car-based), high beam with 9005, close to light lamps 9006 (eg BMW 3 Series, BMW 5 Series, Audi A8, Lexus, sba Lu Impreza, Accord Series, Toyota Camry 2.4, Corolla, Nissan grace, sunshine, Grand Cherokee and other models); also quite a few Japanese models 9004 or 9007 dual-use light bulbs. A modified approach: replacing high-power bulb 1. Conversion methods and principles Such modification methods the simplest and most economic. Is the original car 55/60W (H4) of the ordinary halogen bulbs replaced 90/100W direct high-power light bulbs, and the rest do not make any changes, is one of the most common and easiest way conversion. Its principle is to change the original light bulb small success rate of larger bulbs. Currently the market 90/100W bulb is very large, including many domestic brands, prices are more economical; imports to PHILIPS (Philips) of the most famous silver fighters, soldiers and so blue. After conversion, power was increased, light blue or white hair, the effect has certainly improved. 2. Installation procedures and fees This modified approach is very simple to install, and the same general procedure for replacing the lamp, just after the open headlight cover, replace the bulb, then you can plug the original plug. Costs are more economical, is a pair of new bulbs cost. Ordinary domestic light bulb prices between 10 to 40 yuan; imports of high-grade bulbs PHILIPS price from 200 to 400 yuan. (Note: the prices mentioned in this article refer to aftermarket reference price, retail prices vary.) 3. Use of effects and impact This modified approach, can enhance a certain light intensity, but limited. Bring the lines, switches and a serious increase in power load, increase the heat lamp on the lamp cup of temperature increase, likely to cause the overload of lines and switches burning, accelerated aging mercury lamp cup, resulting in light pillow melting Cup deformation and may lead to fire incidents. The most common failure is that over time, headlight combination switch of contact burning. Because the lamp power increases, the line current follow the increase and in the original line (resistance) remains unchanged, the line voltage loss, which would raise the geometric Power of the power loss increases, the voltage across lamp will drop, leading to increased line load. So, for security reasons, the lamp power for bigger, while lines should be some degree of transformation: Add a relay control, to take power directly from the battery to increase the heat lamp back. Otherwise not only enhance the effect of light brightness is not obvious, but increased security risks. Currently on the market there is a small part of 100/140W bulbs, more powerful, but the results raise is still not clear. And will bring power and load wire and cup serious increase, there is a great security risk, not recommended. Modified way: install headlight brightness enhancement device Headlight brightness enhancement device currently commercially available product, known as line of headlamps by light or brightness enhancement. The essence is installed between the lamp and battery by light, reducing line voltage loss, so that the voltage across the lamp and the battery voltage was close to, credit to small effect. Usually associated with “modified form of a” power with improved light bulb to increase lamp brightness. 1. Conversion methods and principles Original headlight circuit wiring harness from the power supply Insurance switch wiring harness headlights Poor Ground power, after a very long wire to connect battery. Due to wire resistance, the switch contacts, plugs and wiring the impact of exposure status would lead to line resistance increases, headlamps bipolar voltage drop; and headlight brightness enhancement device works is very simple, it does not extra increase the voltage across the lamp, but to use a control relay will headlight battery directly connected to the wires with excellent, so shortening the path, the resistance is also smaller, headlights and battery voltage to maintain consistent, therefore, the original brightness line will increase in comparison, does not occur because the headlight switch, plugs and wires poor contact and weakening of the situation light. Modified approach is to install a set of the original lines from the two relays, 2 Fuse block, 2 lamp socket, a lamp plug, 2 FireWire and bond strap headlight brightness enhancement device package . 2. Installation procedures and fees Basic points are as follows install Step 6: turn off your vehicle power; to the side near the battery unplugging the original car headlights, plug in the booster’s control plug (H4 type font for the goods jaw); the other side of unplugging the original car headlights, wrap and fixed (not floating), then the brightness enhancement device of the two output lines in the two headlights on the plug socket; ear to the ground line output line with

About the Author

We are high quality suppliers, our products such as China bangle bracelet watch , China bangle bracelet watch for oversee buyer. To know more, please visits beaded bracelet watch.

Focus lights converted – converted common mode lights – lights, conversion – Automotive repair and m

More Lighting Articles

 

Start time:  2009-12-09 End time:  2009-12-11 Venue:  China Beijing National Agricultural Exhibition CenterContact:  Cao Cheng China – the development of the world’s largest outdoor Illumination Market China is the world’s urbanization process one of the fastest in the country “to expand domestic demand and promote growth” of the macro-control policy, the future of China will speed up housing projects, railways, highways, airports and other major infrastructure construction, lead Garden District, the stadium, railway stations, airports, ports, squares, communities, attractions and other public facilities to keep growing at more than 16%. March 2009, the National 4 trillion economic stimulus package of infrastructure investment raised from 1.2 trillion yuan, 1.8 trillion yuan, China’s roads, outdoor lighting industry into a new golden age. Face Energy And the environmental crisis, all countries in the efforts to implement the “energy saving” project, with its energy-saving semiconductor lighting Environmental protection The advantages of the national government for its support, which is the development of LED lighting industry offers a great opportunity. China to conform to the trend of carbon reduction, “Eleventh Five-Year Plan” clearly will be the first semiconductor lighting products as key development areas, governments at all levels to promote the expansion needs of the new LED lights.

 

 

Today, there are various types of lights more than 100 million worldwide total more than 500 million street lamp, street lamp market demand in China each year are 20 million or more, and showed a rising trend. Experts predict that the scale of the global LED street lamp shipments expected by the year 2008 rose to 900,000 in 2009 to 2.1 million, penetration is expected to more than 1%, to 2011, is expected to reach 8 million, penetration 8.5%. China is an important global LED street lamp market pioneer, in 2008 demand for 600,000, in 2009 to reach 1.4 million, growing up to 1 times, accounting for 55% global share, 2010,2011 estimated at 2.5 million and 5 million, accounting for global market share of 55% and 59%. Advantage Exhibition 1, Beijing is the capital of China, is China’s political, cultural and economic exchange center, the exhibition not only allows exhibitors directly with China, the northern region of direct interaction between the market, more radiation throughout the entire Asian market. 2, Beijing had 10 billion yuan LED lights transform the huge market opportunity. Types of built-up areas in Beijing city area 1274 square kilometers, is China’s largest city, over 5 thousand km road length, the number of over 300,000 street lamps, lighting, over 10 thousand km line length.

 

Beijing is the capital, widespread use of LED lamps, LED lamps on the promotion of reform in the country is very exemplary and leading sense. 3, Beijing, Tianjin, Hebei, Henan, Shandong, Shanxi, Shaanxi, Inner Mongolia, Gansu, Liaoning, Jilin, Heilongjiang and Hubei, Hunan, Sichuan, Guangxi, Yunnan and Xinjiang provinces about 3500, cities county director of infrastructure and municipal street planning, construction Management Unit support, exhibitors around the country can be a one-time municipal, street management to establish the most direct channels of communication. 4, Beijing and 124 in 72 countries and capital cities have maintained friendly contacts with foreign embassies 137, 190 new foreign institutions, set up in Beijing, the Beijing representative office abroad has more than 7,000 home. Russia, Brazil, India, Indonesia, Thailand, Japan, Korea, Malaysia, Eastern Europe, the Middle East, Southeast Asia nearly 20 countries, construction of municipal street lighting, and the authorities have reached a consensus with the committee, the huge advantage of overseas resources will help this exhibition Overseas exhibitors and professional buyers for the invitation. Events urban and road lighting energy forumresponsible management of the National Lighting Association High-power LED street lampTechnology Forum 2010 National Street Lights Tender Procurement Organizationbuyers 1, by hosting and co-organized, industry, department, organized by red tape in the form of buyers will visit the groups to purchase. 2, the establishment of the buyer database, inviting a select buyers, show promotion group, through direct mail, Electronic E-mail, telephone fax, SMS, etc., invite domestic and foreign buyers from around.

 

3, to various cities of the municipal administration, road lighting Administration / The Leader, municipal design institutes, and units, city road lighting engineering company, landscape lighting company, and real estate developer, garden and scenic construction units, city lighting products and equipment manufacturers boss, Chief Engineer, Electric Engineers, designers and major road projects for persons sent to visit the nearly 20 million volumes, invited to visit the procurement. 4, by 120 professional website, more than 40 professional magazines, newspapers TV Strong promotional platform to invite buyers. 5, he took part in similar exhibitions and street light management activities across the country more than 80 events, with direct invite professional buyers to the meeting. 6, held in “10 City, 10,000″ new energy, new source, forum, invited the country 21 “10 City, 10000″ pilot project city street management director, municipal, urban construction leader, internationally renowned experts academics, manufacturers, operators, government officials and researchers attending the meeting.

 

 

7, the United Nations with the practical engineering of municipal, streetlights and other outdoor lighting project management department to organize exhibitions on-site bidding for the 2010 street project; also be invited to Eastern Europe, the Middle East and Southeast Asian countries, municipal, roads, lighting construction, management agencies in person Show site bidding. Scope of Exhibits Road lamp series: LED street light, pole, solar street lamps, stadium lights, Chinese lamps, tunnel lights; Garden and Landscape: lamp series, lawn, landscape lights, wall lights, corridor lights, fence lights, contour lights, buried lights, underwater lights; LED thematic series: LED components and materials (LED chip, wafer, LED phosphors, organic silicon, substrate, etc.); LED Package / Module (piranha, LED lights, digital tubes, dot matrix LED, cluster-type LED, SMDLED, high-power LED, etc.); LED outdoor lighting applications (LED display, LED landscape lighting, LED lamps lighting, LED architectural lighting, etc.); new energy series: solar photovoltaic products (solar street lamp, lawn lamp, hospital lights, traffic lights, solar lighting systems, solar modules, controllers, inverters, batteries); wind, scenery complementary power generation, lighting system and its ancillary products; City Lighting and Energy: Urban lighting intelligent control and distribution systems, urban lighting energy-saving products